I am have certain issue in configuring VTL on RHEL 5.5, below is my configuration files
----------------------
device.conf
----------------------
VERSION: 5
# VPD page format:
# <page #> <Length> <x> <x+1>... <x+n>
# NAA format is an 8 hex byte value seperated by ':'
# Note: NAA is part of inquiry VPD 0x83
#
# Each 'record' is separated by one (or more) blank lines.
# Each 'record' starts at column 1
# Serial num max len is 10.
# Compression: factor X enabled 0|1
# Where X is zlib compression factor 1 = Fastest compression
# 9 = Best compression
# enabled 0 == off, 1 == on
Library: 30 CHANNEL: 03 TARGET: 00 LUN: 00
Vendor identification: STK
Product identification: L700
Product revision level: 3.14
Unit serial number: 00103800
NAA: 30:22:33:44:ab:03:00:00
Drive: 31 CHANNEL: 03 TARGET: 01 LUN: 00
Library ID: 30 Slot: 01
Vendor identification: STK
Product identification: T10000A
Product revision level: 1.46
Unit serial number: 04003291
NAA: 30:22:33:44:ab:03:01:00
Compression: factor 1 enabled 1
Drive: 32 CHANNEL: 03 TARGET: 02 LUN: 00
Library ID: 30 Slot: 02
Vendor identification: STK
Product identification: T10000A
Product revision level: 1.46
Unit serial number: 04003292
NAA: 30:22:33:44:ab:03:02:00
Compression: factor 1 enabled 1
Drive: 33 CHANNEL: 03 TARGET: 03 LUN: 00
Library ID: 30 Slot: 03
Vendor identification: STK
Product identification: T10000A
Product revision level: 1.46
Unit serial number: 04003293
NAA: 30:22:33:44:ab:03:03:00
Compression: factor 1 enabled 1
Drive: 34 CHANNEL: 03 TARGET: 04 LUN: 00
Library ID: 30 Slot: 04
Vendor identification: STK
Product revision level: 1.46
Product identification: T10000A
Unit serial number: 04003294
NAA: 30:22:33:44:ab:03:04:00
Compression: factor 1 enabled 1
-----------------------------------
library.contents.30
-----------------------------------
Drive 1:
Drive 2:
Drive 3:
Drive 4:
Picker 1:
MAP 1:
MAP 2:
MAP 3:
MAP 4:
# Slot 1 - ?, no gaps
# Slot N: [barcode]
# [barcode]
# a barcode is comprised of three fields: [Leading] [identifier] [Trailing]
# Leading "CLN" -- cleaning tape
# Leading "W" -- WORM tape
# Leading "NOBAR" -- will appear to have no barcode
# If the barcode is at least 8 character long, then the last two characters are Trailing
# Trailing "S3" - SDLT600
# Trailing "X4" - AIT-4
# Trailing "L1" - LTO 1, "L2" - LTO 2, "L3" - LTO 3, "L4" - LTO 4, "L5" - LTO 5
# Training "LT" - LTO 3 WORM, "LU" LTO 4 WORM, "LV" LTO 5 WORM
# Trailing "TA" - T10000+
# Trailing "JA" - 3592+
# Trailing "JB" - 3592E05+
# Trailing "JW" - WORM 3592+
# Trailing "JX" - WORM 3592E05+
#
Slot 1: G03001TA
Slot 2: G03002TA
Slot 3: G03003TA
Slot 4: G03004TA
Slot 5: G03005TA
Slot 6: G03006TA
Slot 7: G03007TA
Slot 8: G03008TA
Slot 9: G03009TA
Slot 10: G03010TA
Slot 11: G03011TA
Slot 12: G03012TA
Slot 13: G03013TA
Slot 14: G03014TA
Slot 15: G03015TA
Slot 16: G03016TA
Slot 17: G03017TA
Slot 18: G03018TA
Slot 19: G03019TA
Slot 20: G03020TA
Slot 21: G03021TA
Slot 22: G03022TA
Slot 23: G03023TA
Slot 24: G03024TA
Slot 25: G03025TA
Slot 26: G03026TA
Slot 27: G03027TA
Slot 28: G03028TA
Slot 29: G03029TA
Slot 30: G03030TA
Slot 31: G03031TA
Slot 32: G03032TA
Slot 33: G03033TA
Slot 34: G03034TA
Slot 35: G03035TA
Slot 36: G03036TA
Slot 37: G03037TA
Slot 38: G03038TA
Slot 39: G03039TA
Slot 40: CLN303TA
-------------------------------------
lsscsi -g output
-------------------------------------
[root@FSPLVTL:/etc/mhvtl]# lsscsi -g
[0:0:0:0] disk ATA ST3500413AS JC45 /dev/sda /dev/sg0
[0:0:1:0] disk ATA WDC WD5000AAKX-0 15.0 /dev/sdb /dev/sg1
[3:3:0:0] mediumx STK L700 3.14 - /dev/sg6
[3:3:1:0] tape STK T10000A 1.46 /dev/st0 /dev/sg2
[3:3:2:0] tape STK T10000A 1.46 /dev/st1 /dev/sg3
[3:3:3:0] tape STK T10000A 1.46 /dev/st2 /dev/sg4
[3:3:4:0] tape STK T10000A 1.46 /dev/st3 /dev/sg5
When i configure the library on a WIN2K8 R2 server using backup software(TSM/Netbackup) then drives are not recognized as a part of library.
As I have seen on the forum that from successful configuration of MHVTL, lsscsi -g gives output like
[2:6:0:0] mediumx STK L700 3.14 /dev/sch6 /dev/sg57
[2:6:1:0] tape STK T10000A 1.46 /dev/st21 /dev/sg25
[2:6:2:0] tape STK T10000A 1.46 /dev/st22 /dev/sg26
[2:6:3:0] tape STK T10000A 1.46 /dev/st23 /dev/sg27
[2:6:4:0] tape STK T10000A 1.46 /dev/st24 /dev/sg28
[2:6:5:0] tape STK T10000A 1.46 /dev/st25 /dev/sg29
What I analyse while comparing the output of lsscsi -g is as below
my MHVTL- lsscsi output
[3:3:0:0] mediumx STK L700 3.14 - /dev/sg6
One i found on the forum
[2:6:0:0] mediumx STK L700 3.14 /dev/sch6 /dev/sg57The difference is of /dev/sch6, wherein my MHVTL lsscsi output should give
[3:3:0:0] mediumx STK L700 3.14 /dev/sch3 /dev/sg6
Now if anybody could help me out finding where I am doing any mistake or the configuration is wrong.
Locked
